Ohm's law
V = I × R I = V ÷ R R = V ÷ I
Know any two of voltage, current and resistance and you can find the third. A 12 V supply across a 60 Ω resistor drives 12 ÷ 60 = 0.2 A. To limit the current to 0.05 A from the same supply you need 12 ÷ 0.05 = 240 Ω.
Common ranges
| Unit | Ohms | Where you meet it |
|---|---|---|
| milliohm (mΩ) | 0.001 | Cables, connectors, current shunts |
| ohm (Ω) | 1 | Loudspeakers, heating elements |
| kilohm (kΩ) | 1,000 | Most resistors in electronics |
| megohm (MΩ) | 1,000,000 | Insulation, high-impedance inputs |
Resistance turns electricity into heat
Current flowing through resistance produces heat. The power is P = I² × R, or equivalently P = V² ÷ R. This is useful in a kettle or toaster, and wasteful in a cable. It is also why every resistor has a power rating that must not be exceeded.
Series and parallel
- Series: resistances add. Two 100 Ω resistors in series make 200 Ω.
- Parallel: conductances add. Two 100 Ω resistors in parallel make 50 Ω, and the total is always less than the smallest branch.
What sets the resistance of a wire
R = resistivity × length ÷ cross-sectional area
A longer wire has more resistance and a thicker wire has less. The material matters through its resistivity: copper is about 1.68 × 10⁻⁸ Ω·m and aluminum about 2.65 × 10⁻⁸ Ω·m, which is why aluminum cables are made thicker for the same job.
Temperature matters too. The resistance of copper rises by about 0.39% per degree Celsius, so a hot cable drops more voltage than a cold one.
Resistance and conductance
Conductance is the reciprocal of resistance, measured in siemens. A 4 Ω resistor has a conductance of 0.25 S. The same idea applied to materials gives conductivity, the reciprocal of resistivity.
When Ohm's law does not apply
Ohm's law describes components whose resistance stays constant. LEDs, diodes and transistors have a strongly non-linear relationship between voltage and current. A filament lamp follows the law only roughly, because its resistance rises many times over as it heats up.
Frequently asked questions
What is one ohm?
The resistance that allows one ampere to flow when one volt is applied.
Does a thicker wire have more or less resistance?
Less. Resistance is inversely proportional to cross-sectional area, so doubling the area halves the resistance.
Why is adding a resistor in parallel always guaranteed to lower the total resistance?
Adding a parallel branch opens an additional path for current to flow. Even if you connect a huge 1,000 Ω resistor in parallel with a 10 Ω resistor, the combined resistance (1 / (1/10 + 1/1000) = 9.90 Ω) is strictly smaller than the smallest individual branch.
What is the shortcut formula for just two resistors in parallel?
Use 'product over sum': R_total = (R1 × R2) ÷ (R1 + R2). For two identical 100 Ω resistors in parallel, (100 × 100) ÷ 200 = 50 Ω (exact half).
Why do high-voltage transmission lines use 400 kV instead of 230 V?
Because power transmitted is P = V × I while resistive heat loss in the cables is P_loss = I² × R. Raising voltage by 1,000× cuts current (I) by 1,000× for the same power—which reduces I²R line losses by a factor of **1,000,000** (1,000²).
Related guides
Worked example: Voltage drop across 30 meters of 2.5 mm² copper wire carrying 16 A
Suppose an outdoor workshop socket is fed by a 30-meter cable run using 2.5 mm² copper wire (ρ = 1.72 × 10⁻⁸ Ω·m at 20 °C) and carries a load current of 16 A on a 230 V circuit:
- Step 1 — Total round-trip conductor length (
L): Current flows 30 m out on the live wire and 30 m back on the neutral wire, so total copper pathL = 30 × 2 = 60 meters. - Step 2 — Convert cross-sectional area (
A) to square meters:2.5 mm² = 2.5 × 10⁻⁶ m². - Step 3 — Wire loop resistance (
R = ρ × L / A):R = (1.72 × 10⁻⁸ × 60) ÷ (2.5 × 10⁻⁶) = 1.032 × 10⁻⁶ ÷ (2.5 × 10⁻⁶) =0.4128 Ω. - Step 4 — Voltage drop (
V = I × R) and heat loss (P = I² × R):- Voltage drop:
16 A × 0.4128 Ω =6.60 V (2.87%drop on a 230 V line, leaving223.4 Vat the tool). - Power wasted as cable heat:
16² × 0.4128 Ω = 256 × 0.4128 =105.7 W.
- Voltage drop:
Limits and AC vs DC differences
- DC resistance vs AC impedance (
Z): Ohm's Law (V = I × R) describes pure resistive circuits. In AC circuits containing inductors (motors, transformers) or capacitors, reactance (X_LandX_C) combines with resistance to form total **impedance (Z = √(R² + X²)in ohms)**. - Temperature coefficient of copper (
+0.393%per °C): As a loaded cable heats up from 20 °C to 70 °C (+50 °C), its resistance rises by nearly **20%** (0.413 Ω → 0.494 Ω), increasing voltage drop further.