Density
density = mass ÷ volume
The SI unit is the kilogram per cubic meter. Grams per cubic centimeter is also common because water comes out at almost exactly 1. To convert, 1 g/cm³ = 1,000 kg/m³.
| Material | kg/m³ | g/cm³ | lb/ft³ |
|---|---|---|---|
| Air (sea level, 15 °C) | 1.225 | 0.0012 | 0.0765 |
| Pine wood | 500 | 0.50 | 31 |
| Gasoline | 740 | 0.74 | 46 |
| Ice | 917 | 0.917 | 57.2 |
| Water (4 °C) | 1,000 | 1.00 | 62.4 |
| Concrete | 2,400 | 2.40 | 150 |
| Aluminum | 2,700 | 2.70 | 169 |
| Steel | 7,850 | 7.85 | 490 |
| Lead | 11,340 | 11.34 | 708 |
| Gold | 19,300 | 19.30 | 1,205 |
Values for wood, concrete and fuels vary with type and moisture, so treat them as typical.
Specific gravity
Specific gravity, also called relative density, is the density of a substance divided by the density of water. It has no unit. A value below 1 floats in water, and a value above 1 sinks.
Since water is about 1 g/cm³, the specific gravity of a material is numerically almost the same as its density in g/cm³. Steel at 7.85 g/cm³ has a specific gravity of 7.85.
Using density to convert volume to weight
Volume and mass are different quantities and cannot be converted without knowing what the substance is. Density provides the link:
mass = density × volume
A 200-liter drum of gasoline holds 0.2 m³ × 740 kg/m³ = 148 kg of fuel. The same drum filled with water would hold 200 kg. This is why "how many grams in a cup" has no single answer: it depends on the ingredient.
Why ice floats
Most substances are denser as solids than as liquids. Water is unusual: ice is about 8% less dense than liquid water, so it floats with roughly 92% of its volume below the surface. In seawater, which is denser, a little more shows.
Temperature and pressure
Density changes with temperature. Liquids and solids expand slightly when heated, so density figures quote a reference temperature. Gases change dramatically: air at the top of Mount Everest is about a third as dense as at sea level.
Frequently asked questions
What is the density of water?
About 1,000 kg/m³ (1 g/cm³) at 4 °C, where it is densest. At 20 °C it is about 998 kg/m³.
Is specific gravity the same as density?
No. Density has units and specific gravity is a ratio without units. Numerically, specific gravity equals density in g/cm³ to a close approximation.
Why does Specific Gravity have no units?
Because Specific Gravity divides one density (kg/m³) by another density (kg/m³), the units cancel out completely—leaving a dimensionless ratio that is the exact same number whether you work in metric (kg/m³) or imperial (lb/ft³).
What is API Gravity in the petroleum industry?
The American Petroleum Institute (API) uses an inverted scale: API Gravity = (141.5 ÷ SG at 60°F) − 131.5. Fresh water (SG = 1.00) has an API gravity of 10°, while lighter, higher-value crude oils have higher API numbers (such as 38°–40° API for West Texas Intermediate).
How is gas specific gravity defined?
For gases (like natural gas or propane), specific gravity is usually measured relative to dry air at the same temperature and pressure (ρ_air ≈ 1.225 kg/m³ at 15 °C, sea level) rather than liquid water. Methane (SG ≈ 0.55) rises in air, while propane (SG ≈ 1.52) sinks to the floor.
Related guides
Worked example: Finding the weight of 200 liters of diesel fuel and checking battery electrolyte SG
Here are two practical engineering calculations using density (ρ = m / V) and specific gravity (SG = ρ_substance / ρ_water):
- Example 1 — Mass of a 200-liter drum of diesel fuel (
SG = 0.835):- Because water at 4 °C has a density of
1.000 kg/L(1,000 kg/m³), a liquid withSG = 0.835has a density of0.835 kg/L(835 kg/m³). - Multiply volume by density:
200 L × 0.835 kg/L =167.0 kg (368.2 lb) of fuel (plus the ~18 kg tare weight of the steel drum = ~185 kg gross lift).
- Because water at 4 °C has a density of
- Example 2 — Lead-acid battery hydrometer reading (
SG = 1.265at 25 °C): A fully charged 12 V flooded lead-acid battery contains sulfuric acid electrolyte that is1.265times denser than pure water (1,265 kg/m³), whereas a discharged battery drops toward1.120as sulfate ions move onto the lead plates.
Limits and common reference pitfalls
- Reference water temperature matters for 4-digit laboratory precision: Pure water hits its maximum density of
999.972 kg/m³(≈ 1.000 g/cm³) at **4 °C (39.2 °F)**. At room temperature (**20 °C**), water expands slightly to998.207 kg/m³. Always check whether a hydrometer is calibrated to20 °C / 20 °Cor60 °F / 60 °F(15.56 °C). - Bulk density vs true particle density: Dry sand, gravel, cement, and grain have air gaps between particles. Solid quartz rock has a true density of
2,650 kg/m³(SG = 2.65), but loose dry builder's sand in a bucket has a *bulk density* of only1,450 to 1,600 kg/m³due to ~40% void space.